Preseason Field Check of Planting Equipment

Preseason Field Check of Planting Equipment

As you wait to start planting, take time now to check on how well your planter will perform in the field. As with any piece of equipment, the operator’s manual is the starting point for the initial settings and adjustments. Recommendations and trouble-shooting tips are available in the manual and from others who own and operate similar equipment.

Planter in cover crops
Figure 1. The toolbar on this planter is at the correct height as the parallel links on the row units are running level. The planter is leveled slightly tail down to improve seed-to-soil contact by raising the hitch point on the tractor. Weights have been added to the row units to ensure penetration to the desired seeding depth.  Weight has been added to the toolbar (by putting water in the fertilizer tanks) to keep the drive wheels in firm contact with the ground while the downpressure springs transfer some weight to the row units.

In the off season, you should have checked all sprockets, chains, bearings, and related drive components for wear and replaced parts as necessary. Likewise, the seed meters should have been cleaned and maintained at the end of last planting season before putting the planter away for storage. If these maintenance items were not performed then, do so now to minimize downtime during the planting season. Remember, the best time to check over the planter and make the appropriate repairs is at the end of the planting season while everything is still fresh in mind.

Make sure the tires are properly inflated so that the drive wheels turn the seed meters as designed. Even on planters with hydraulic or electric drives, the tires need to be properly inflated so that the toolbar is at the correct height and level from side-to-side. Level the planter front to back in the field, not at the shop, as the tires and row units sink into the soil differently compared to sitting on concrete. While in the field, check and adjust your planter to improve its performance. By doing this before planting season, you will save valuable time at planting.

  1. Level the planter, making sure that the toolbar is at the proper height and leveled front-to-rear, perhaps even slightly “tail” down. This allows for the full range of movement of the parallel links on the row units and aids in seed-to-soil contact. If the toolbar is too high, the downpressure springs are ineffective. If the toolbar is too low, you may break downpressure springs by over-extending them.

  2. Make sure the planter carrying wheels are centered between the row units and carrying some weight. This is especially important for producers using the ridge-plant system to help keep the planter on top of the ridge.  Remember that the toolbar height will change by the height of the ridges and needs to be reset as the carrying wheels settle into the furrow.

  3. Once the planter is leveled, try blind planting with no seed in the boxes or other products on the planter (everything empty as that’s the lightest the planter will be). Stop with the planting units in the ground and check to see if the depth gauge wheels are in firm contact with the soil. If they are not, tighten the downpressure springs (or increase the air pressure on the airbags, if so equipped) and try planting again. If you cannot tighten the springs, you may have to add extra springs or add weight directly to the row unit to get the gauge wheels in firm contact with the soil. Conversely, if you cannot slip the depth gauge wheels slightly, especially on wetter soils, you may have to reduce the downpressure to avoid over-compacting the soil next to the seed-vee.

  4. Check to see if you can slip the seed meter drive wheels as the downpressure springs will be lifting the toolbar. You may have to add weight to the planter frame for the springs or airbags to work against and to keep the drive wheels firmly on the ground to reduce slip. Don’t loosen the springs to get the drive wheels back in contact with the soil as penetration to seeding depth is necessary. Extra weight will be needed for dry soils or heavy residue and on planters with inter-plant units.

  5. Place a small amount of seed into a couple of seed boxes and plant a short distance. Check seeding depth, seed-to-soil contact, seeding depth uniformity, and seed spacing uniformity. Evaluate seed-vee closing and check to make sure you’re not over compacting the seed zone or packing below the seeding depth.

 Make the necessary adjustments or add the required equipment to improve planter performance and check the planter again. Even though a preseason planter check was made, all of these items should be rechecked when actual planting begins and as conditions change during the planting season.

Tags: 

Online Master of Science in Agronomy

With a focus on industry applications and research, the online program is designed with maximum flexibility for today's working professionals.

A field of corn.